Solid State Relays – Robosupersun

8-Channel 5V Solid State Relay Module Board for Arduino Uno Duemilanove MEGA2560 MEGA1280 ARM DSP PIC

Admin — Mon, 26 Feb 2024 05:59:34 +0000

Specification:

Operating Voltage: 5V
Operating Current: 16mA
Maximum Load: 2A @ 240VAC
8 channel 2 AMP Solid State Relay board
Control 8 loads of up to 2 amps each at 120V or 240V AC.
SSR Output (each channel):
- Load voltage range: 75 to 264V AC (50/60Hz).
- Load current: 0.1 to 2 AMP.
Input control signal voltage:
- 0V - 0.5V Low stage (SSR is Off).
- 0.5V - 2.5V (unknown state).
- 2.5V - 20V High state (SSR is On)

…

DC To AC SSR-100DA Solid State Relay Module 3-32VDC/24-380VAC 100A

Admin — Mon, 26 Feb 2024 05:56:34 +0000

This is DC To AC SSR-100DA Solid State Relay Module 3-32VDC/24-380VAC 100A. A solid state relay (SSR) is an electronic switch, which, unlike an electromechanical relay, contains no moving parts. The types of SSR are photo-coupled SSR, transformer-coupled SSR, and hybrid SSR. A photo-coupled SSR is controlled by a low voltage signal which is isolated optically from the load.

The control signal in a photo-coupled SSR typically energizes an LED which activates a photo-sensitive diode. The diode turns on a back-to-back thyristor, silicon controlled rectifier, or MOSFET transistor to switch the load.

This particular SSR can switch current loads of up to 100A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.

Features :

Long service life and high reliability
Reduced electromagnetic interference
Highly reliable, compact size designed to offer users maximum simplicity.

Specification :

Rated Load Current (mA) : 100A
Dielectric Strength : Over 2.5kVA / 1 min
Trigger Voltage (VDC) : 3-32
Switching Voltage (VAC) : 24-380@100A
Operating Temperature Range (C) : -20 to 85
Material : ABS

5V 1 Channel Solid State Relay 1 Channel 5V Relay Module Solid State High Level SSR DC Control 250V 2A with Resistive Fuse

Admin — Mon, 26 Feb 2024 05:55:41 +0000

This is a 5V 1 Channel Solid State Relay Module. A solid-state relay (SSR) is just what it sounds like, an IC that acts like a mechanical relay. They allow you to control high-voltage AC loads from lower-voltage DC control circuitry. They accomplish this by using infrared light as the ‘contact,’ a solid-state relay is just an IR LED and a photo Triac sealed up into a little box. Solid-state relays have several advantages over mechanical relays.

A State Relay is similar to a 5V 1 Channel Solid State Relay High-Level SSR DC Control 250V 2A with Resistive to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan compared to the traditional mechanic relay.

Features:

5V 1 Channel Solid State Relay can be controlled directly by a Microcontroller
Led indicator for each relay.
Control 1 load of up to 2 amps each at 240 V AC.
Use it to control various appliances and other equipment with a large current

DC To AC SSR-25DA Solid State Relay Module 3-32 VDC /24-380VAC 25A

Admin — Mon, 26 Feb 2024 05:54:19 +0000

This is DC To AC SSR-25DA Solid State Relay Module 3-32VDC/24-380VAC 25A. A solid-state relay (SSR) allows you to control high-current AC loads from lower voltage DC control circuitry. Solid-state relays have several advantages over mechanical relays. One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there are no moving contacts, solid-state relays can be switched much faster and for much longer periods without wearing out. This particular SSR can switch current loads of up to 25A with a 3-32V DC input and a zero cross trigger control method. Each one of these relays is equipped with four screw terminals (for use with ring or fork connectors) and a plastic cover that slides over the top of the relay to protect the terminals.

Specification:

Model: SSR-25DA
Rated Load Current: 25A
Trigger Voltage: 3-32V DC
Switching Voltage: 24-380@25A

5V 4-Channel Solid State Relay Board, Solid State Relay Modul, High and Low Level Trigger

Admin — Mon, 26 Feb 2024 05:53:14 +0000

This 5V 4 Channel SSR Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the G3MB SSR relay which can control up to 2A at 240VAC. This is a 4 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed). A solid-state relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay. When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.

Specification:

Part Number	G3MB-202P
Voltage	5V
Working Current	12.5 mA
Trigger Voltage	3.3 to 5V
Trigger Current	2 mA
Max. Load	2A @240V AC

Features:

Has been assembled, and the electrical test passed.
Led indicator for each relay.
Use it to control various appliances and other equipment with a large current.
It can be controlled directly by a Microcontroller
Input control signal voltage:
- 0-2.5V status low level, relay OFF
- 3-5V status high level, relay ON

Input Section:

DC +: positive power supply (by relay voltage power supply)
DC-: connect power negative
CH1: 1 relay module signal to trigger the end (high-level trigger effective)
CH2: 2-channel relay module signal to trigger the end (high-level trigger effective)
CH3: 3 relay module signal to trigger the end (high-level trigger effective)
CH4: 4-channel relay module signal to trigger the end (high-level trigger effective)

Voltage version	static current	working current	trigger voltage	trigger current
1 road 5v	0mA	13.8mA	3.3-5V	2mA
2 road 5v	0mA	26.8mA	3.3-5V	2mA
3 road 5v	0mA	37mA	3.3-5V	2mA
4 road 5v	0mA	48mA	3.3-5V	2mA

5V 8 Channel Solid State Relay Module 5v Solid State Relay Low Level Trigger Solid State Relay Module

Admin — Mon, 26 Feb 2024 05:51:57 +0000

This 5V 2A 8-Channel SSR Solid State Relay Module is based on the G3MB SSR relay which can control up to 2A at 240VAC. This is an 8 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed). A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay. When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load. 5V 2A 8-Channel SSR Solid State Relay Module Can be directly controlled by Arduino and other microcontrollers It is Eight channels relay interface board able to control various appliances and equipment with large current.

Specification:

Trigger Type: Low Level Trigger
Working Current: 16mA
Trigger Current: 2Ma
Trigger Voltage: 5v dc
Switching Voltage: AC 240V @2A
Isolation: Phototriac
The Input Control Signal Voltage: (0-0.5V low solid state relay OFF) (2.5-20V high solid state relays ON)

Features:

8 channel 2 AMP Solid State Relay board
Control 8 loads of up to 2 amps each at 120V or 240V AC.
Good for lighting, holiday displays etc.
Has been assembled, and the electrical test passed.
Led indicator for each relay.
Use it to control various appliances and other equipment with a large current.
It can be controlled directly by Microcontroller

Interface:

DC+: positive power supply (relay voltage power supply)
DC-: connect power negative
CH1: 1 signal to trigger the end of the relay module (low level trigger valid)
CH2: 2-way relay module signal triggering end (low level trigger valid)
CH3: 3 relay module signal triggering end (low level trigger valid)
CH4: 4-channel relay module signal triggering end (low level trigger valid)
CH5: 5-way relay module signal triggering end (low level trigger valid)
CH6: 6-way relay module signal triggering end (low level trigger valid)
CH7: 7-way relay module signal triggering end (low level trigger valid)
CH8: 8-channel relay module signal triggering end (low level trigger valid)

Note:

Power must be DC voltage and need to be consistent with the voltage relay. The Board is available in Red Color.
This Relay module is a Low-Level Trigger Module. Please note it before purchase.
Product Image May vary in terms of Brand Name on relay according to the availability of Supplier

5V 1 Channel Solid State Relay Module Board for AC 240V/2A Arduino Uno MEGA2560 MEGA1280 ARM DSP PIC

Admin — Mon, 26 Feb 2024 05:50:30 +0000

Features:

5V operating voltage,
The max connected load is ac 240V/ 2A,
It also has a resettable fuse to protect the module
With power anti-reverse function,
It will not damage the module if connecting the wrong power supply
With the good anti-interference ability
Stable performance
The triggering current is only 1Ma
High-level controlled module
Built-in limiting resistors

…

5V 2 Channel G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse

Admin — Mon, 26 Feb 2024 05:49:10 +0000

A two-channel relay module (HCMODU0115) featuring 2x Omron G3MB-202P solid state relays. This 5V 2 Channel SSR G3MB-202P Solid State Relay Module is capable of switching AC voltages between 100 and 240V at up to a 2A current. The module can be controlled from a 5V digital source such as an Arduino microcontroller. A resistive type fuse is provided on the module to help protect excessive current draw. This 5V 2 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 2 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed). A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay. When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.

Specification:

Part Number: G3MB-202P
Voltage: 5V
Working Current: 16mA
Isolation: Phototriac
Max. Load: 2A @240V AC

Features:

2 channel 2 AMP Solid State Relay board
Control 2 loads of up to 2 amps each at 120V or 240V AC.
Good for lighting, holiday displays etc.
Has been assembled, and the electrical test passed.
Led indicator for each relay.
Use it to control various appliances and other equipment with a large current.
It can be controlled directly by Microcontroller
The 2.54CM pin and blue KF301 terminal are connected to the line of control.
Input control signal voltage:
- 0-0.5V the state of low-level relay OFF
- 0.5-3.3V Unknown State
- 3.3-5V high-level relay ON

Input Section:

DC+: Connect the positive pole of the power supply (powered by the relay voltage)
DC-: Connected to the negative pole of the power supply
CH1:1 relay module signal trigger end (high-level trigger effective)
CH2:2 relay module signal trigger end (high-level trigger effective)

High And Low Meaning:

High-level trigger refers to the signal trigger end (IN) had a positive voltage and the negative pole of the power supply is usually between, and the triggering end of a trigger connected with the positive pole of a power supply, when the trigger end has a positive voltage or reached the trigger voltage, the relay is attracted.
Low-level trigger refers to the signal triggering voltage between the end and the negative electrode of the power supply is OV, or trigger terminal voltage lower voltage than the positive power supply voltage, low to can trigger, make the relay, is usually the cathode of the power supply and the triggering end of a trigger mode connection, so that the relay is attracted.